Just How to Install a Bath Tub Yourself: Removing as well as Replacing.

Additional Resources

They are making a few good points regarding Tools You Need to Install a New Bathtub as a whole in the content underneath.


Installing A Bathtub
Mounting a bath tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub as well as place the new tub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will certainly require an assistant to leave the old tub as well as set in the brand-new one. Make sure you have actually certified on your own for the work and also fit trying it. Instead of hiring a professional to take over a halfway-completed task, it is far better to take into consideration using one prior to you begin. Possibilities are you may require an expert plumber to make tube connections.
This post will assist you install a new bathtub in your bathroom if you have actually currently acquired a brand-new bathtub and also don't need to change the arrangement of your previous water supply pipes.
Your tools and also product list must consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Planning for the Installment


    To start with, the supporting framework supplied with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to stop pressure on the bathtub.
    Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washers.
    Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.

    Removing Old Taps


    If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the water. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be quite troublesome due to the limited accessibility that is typically the instance.
    Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
    Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Bath tub


    Making use of the two wooden boards under its feet, put the bathtub in the required position. The wood boards are helpful in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
    The next objective is to make certain that the tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
    To install taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; then do the same for the other tap.
    Switch on the water supply and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the tub and also check the overflow outlet and also the regular outlet for leaks.
    Ultimately, repair the bathroom paneling as explained in the supplier's user's manual. Tiling as well as securing around the tub ought to wait until the bathtub has actually been utilized at least once as this will certainly settle it right into its last position.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a link to the existent supply pipes.
    If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next off, position the faucet in the installing opening in the bath/basin making sure that the washing machines are in area between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The former type should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.

    Tiling Around the Tub


    In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall between the bathroom as well as the tiling, resulting in complications with moisture and feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealer can crack fairly very early if you do not take into account this motion prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I have been very focused on How to Install a Bathtub and I'm hoping you enjoyed the blog posting. Be sure to take a moment to share this entry if you enjoyed reading it. Thanks a lot for taking the time to read it.



    Details Here

    Leave a Reply

    Your email address will not be published. Required fields are marked *